ACCULOGIC, INC.
SIDE-4/ PLUS
|
| |
|
Data bus: |
16-bit, ISA |
|
Size: |
Half-length, full-height card |
|
Hard drives supported: |
Two IDE(AT) drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
34-pin control cable connector-floppy drive |
J1 |
|
4-pin connector-drive active LED |
J2 |
|
40-pin AT Interface (IDE) connector |
J3 |
|
9-pin serial port 2-internal |
J4 |
|
15-pin game port-internal |
J5 |
|
9-pin serial port 1-external |
J6 |
|
25-pin parallel port-external |
J7 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
I/O Channel Ready signal disabled |
JP4 |
open | |
|
I/O Channel Ready signal enabled |
JP4 |
closed | |
|
Floppy drive enabled |
JP5 |
pins 1 & 2 closed | |
|
Floppy drive disabled |
JP5 |
pins 2 & 3 closed | |
|
Floppy drive port address is 3F0-3F7h |
JP6 |
pins 1 & 2 closed | |
|
Floppy drive port address is 370-377h |
JP6 |
pins 2 & 3 closed | |
|
Single speed floppy drives supported |
JP7 |
pins 1 & 2 closed | |
|
Dual speed floppy drives supported |
JP7 |
pins 2 & 3 closed | |
|
Hard drive enabled |
JP8 |
pins 1 & 2 closed | |
|
Hard drive disabled |
JP8 |
pins 2 & 3 closed | |
|
IDE select mode enabled |
JP9 |
pins 1 & 2 closed | |
|
Not used |
JP9 |
open | |
|
Hard drive port address is 1F0-1F7h |
JP10 |
pins 1 & 2 closed | |
|
Hard drive port address is 170-177h |
JP10 |
pins 2 & 3 closed | |
|
Not used |
JP11 |
open | |
|
IRQ14 normal |
JP12 |
pins 1 & 2 closed | |
|
IRQ14 delayed until ACTIVE- signal is removed |
JP12 |
pins 2 & 3 closed | |
|
SERIAL & PARALLEL PORT CONFIGURATIONS | |||
|
Function |
Location |
Setting | |
|
Serial port 1 (CN6) enabled |
JP13 |
pins 1 & 2 closed | |
|
Serial port 1 (CN6) disabled |
JP13 |
pins 2 & 3 closed | |
|
Serial port 1 (CN6) set to COM1 |
JP14 |
pins 1 & 2 closed | |
|
Serial port 1 (CN6) set to COM3 |
JP14 |
pins 2 & 3 closed | |
|
Serial port 2 (CN4) enabled |
JP15 |
pins 1 & 2 closed | |
|
Serial port 2 (CN4) disabled |
JP15 |
pins 2 & 3 closed | |
|
Serial port 2 (CN4) set to COM2 |
JP16 |
pins 1 & 2 closed | |
|
Serial port 2 (CN4) set to COM4 |
JP16 |
pins 2 & 3 closed | |
|
Parallel port (CN7) enabled |
JP17 |
pins 1 & 2 closed | |
|
Parallel port (CN7) disabled |
JP17 |
pins 2 & 3 closed | |
|
Parallel port (CN7) address is LPT1 |
JP18 |
pins 1 & 2 closed | |
|
Parallel port (CN7) address is LPT2 |
JP18 |
pins 2 & 3 closed | |