IPTool.net.ua IPTools.net.ua

VIVA 24M

COMPUTER PERIPHERALS, INC.

VIVA 24M

Modem Type

Data (synchronous/asynchronous)

Maximum Data Rate

2400bps

Data Bus

External

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis

Error Correction/Compression

MNP5

CONNECTIONS

Purpose

Location

Purpose

Location

Line out

CN1

DC power

CN4

Line in

CN2

Power switch

SW1

RS-232/422

CN3

   

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

HS

Red

On

Modem is operating at 2400bps

HS

Red

Off

Modem is operating at slower than 2400bps

AA

Red

On

Auto-answer enabled

AA

Red

Off

Auto-answer disabled

AA

Red

Blinking

Phone is ringing

CD

Red

On

Carrier signal detected

CD

Red

Off

Carrier signal not detected

OH

Red

On

Modem is off-hook

OH

Red

Off

Modem is on-hook

RD

Red

On

Modem is receiving data

RD

Red

Off

Modem is not receiving data

SD

Red

On

Modem is transmitting data

SD

Red

Off

Modem is not transmitting data

TR

Red

On

DTR signal is high

TR

Red

Off

DTR signal is low

MR

Red

Blinking

Loopback tests enabled

MR

Red

On

Power is on

MR

Red

Off

Power is off

Note: The LEDs are Icons.

Proprietary AT Command Set

ACCEPT RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \U

Example:

AT \U <CR>

Description:

Accepts remote modems request for reliable link.

AUTO-RELIABLE FALLBACK CHARACTER

Type:

Configuration

Format:

AT [cmds] %An [cmds]

Example:

AT %A0 <CR>

Default:

Unidentified

Range:

0-127

Unit:

ASCII

Description:

Sets the character used as the auto-reliable fallback character. %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION

Type:

Configuration

Format:

AT [cmds] \Cn [cmds]

Example:

AT \C0 &W<CR>

Description:

Controls the handling of incoming data during auto-reliable time period.

Command

Function

\CO

Data is discarded.

\C1

Data is buffered.

\C2

Data is discarded, sets to normal mode and sends auto-reliable character to serial port.

BREAK SEND

Type:

Configuration

Format:

AT [cmds] \Bn [cmds]

Example:

AT \B3 <CR>

Default:

3

Range:

1-9

Unit:

.1 second

Description:

Sends break to modem.

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Example:

AT \K5 <CR>

Description:

Configures action of break signal.

Command

Break from DTE

Reliable/Normal mode

Break from DTE

Direct mode

Break from remote modem

Modem receives \B

\K0

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Buffers cleared and break sent to DTE.

Buffers cleared and break sent to remote modem.

\K1

Buffers cleared and break sent to remote modem.

Send break to remote modem immediately.

Buffers cleared and break sent to DTE.

Buffers cleared and break sent to remote modem.

\K2

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Send break to DTE immediately.

Send break to remote modem immediately.

\K3

Send break to remote modem immediately.

Send break to remote modem immediately.

Send break to DTE immediately.

Send break to remote modem immediately.

\K4

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Break sent with received data to the DTE.

Send break to remote modem with transmitted data.

\K5

Send break with transmitted data.

Send break to remote modem immediately.

Break sent with received data to the DTE.

Send break to remote modem with transmitted data.

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Example:

AT %C1 <CR>

Description:

Selects data compression.

Command

Function

%C0

Data compression disabled.

%C1

Data compression enabled.

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Example:

AT \N1 <CR>

Description:

Sets connect mode.

Command

Function

\N0

Normal mode enabled.

\N1

Direct mode enabled.

\N2

Reliable mode enabled.

\N3

Auto-reliable mode enabled.

CONVERT TO RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \Y

Example:

AT \Y <CR>

Description:

Initiates reliable mode link.

DISPLAY CURRENT COMMAND STATUS

Type:

Immediate

Format:

AT [cmds] \S [cmds]

Example:

AT \S <CR>

Description:

Displays current setting of modem commands.

ECHO DATA

Type:

Configuration

Format:

AT [cmds] \En [cmds]

\Example:

AT \E0 <CR>

Description:

Enables modem to echo received data.

Command

Function

\E0

Data echo disabled.

\E1

Data echo enabled.

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \Gn [cmds]

Example:

AT \G0 <CR>

Description:

Selects modem port flow control.

Command

Function

\G0

Flow control disabled.

\G1

Flow control enabled.

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Example:

AT \Q0 <CR>

Description:

Sets type of flow control used by modem.

Command

Function

\Q0

Flow control disabled.

\Q1

XON/XOFF flow control enabled.

\Q2

CTS flow control to DTE enabled.

\Q3

RTS/CTS flow control enabled.

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Example:

AT\T0 <CR>

Default:

0

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects.

Note: \T0 will disable inactivity timer.

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] \Jn [cmds]

Example:

AT \J1 <CR>

Description:

Sets operation of serial port speed.

Command

Function

\J0

Serial speed locked.

\J1

Serial speed follows connect speed.

MAXIMUM BLOCK SIZE FOR TRANSMISSION

Type:

Configuration

Format:

AT [cmds] \An [cmds]

Example:

AT \A3 %C1<CR>

Description:

Sets the maximum transmittable block size.

Command

Function

\A0

MNP block size is 64 characters.

\A1

MNP block size is 128 characters.

\A2

MNP block size is 192 characters.

\A3

MNP block size is 256 characters.

MNP RESULT CODES

Type:

Configuration

Format:

AT [cmds] \Vn [cmds]

Example:

AT \V1 <CR>

Description:

Selects MNP result codes.

Command

Function

\V0

MNP result codes disabled.

\V1

MNP result codes enabled.

MNP STREAM/BLOCK MODE

Type:

Configuration

Format:

AT [cmds] \Ln [cmds]

Example:

AT \L0 <CR>

Description:

Selects the transfer mode for MNP.

Command

Function

\L0

Stream mode for MNP enabled.

\L1

Block mode for MNP enabled.

ON-LINE IN RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \O

Example:

AT \O <CR>

Description:

Returns to on-line and requests reliable mode connection.

SWITCH TO MNP MODE

Type:

Immediate

Format:

AT [cmds] \Z

Example:

AT \Z <CR>

Description:

Switches to normal mode from MNP mode.

XON/XOFF PASS-THROUGH

Type:

Configuration

Format:

AT [cmds] \Xn [cmds]

Example:

AT \X0 <CR>

Description:

Selects whether XON/XOFF signals are sent to remote modem.

Command

Function

\X0

XON/XOFF signals trapped by local modem.

\X1

XON/XOFF passed through local modem.