LANNER ELECTRONICS, INC.
AP-300AA
|
Device Type |
Mainboard |
|
Processor |
CX 486SLC/CX486SLC2/AM386SX |
|
Processor Speed |
33/40/50(internal)MHz |
|
Chip Set |
ALI |
|
Video Chip Set |
None |
|
Maximum Onboard Memory |
16MB |
|
Maximum Video Memory |
None |
|
Cache |
None |
|
BIOS |
AMI |
|
Dimensions |
185mm x 122mm |
|
I/O Options |
Floppy drive interface, IDE interface, parallel port, serial ports (2), PC/104 connectors (2) |
|
NPU Options |
None |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
PC/104 connector (8-bit) |
CN1 |
Turbo switch |
J2 |
|
PC/104 connector (16-bit) |
CN2 |
Turbo LED |
J3 |
|
IDE interface |
CON1 |
Reset switch |
J4 |
|
Floppy drive interface |
CON2 |
IDE interface LED |
J5 |
|
Parallel port |
CON3 |
Speaker |
J6 |
|
Serial port 1 |
CON4 |
External battery |
J7 |
|
Serial port 2 |
CON5 |
Auxiliary keyboard connector |
KB1 |
|
Power LED & keylock |
J1 |
External power |
PS1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
|
|
Flash BIOS voltage select 12v |
JP1 |
Pins 1 & 2 closed |
|
Flash BIOS voltage select 5v |
JP1 |
Pins 2 & 3 closed | |
|
|
BIOS type select flash |
JP2 |
Pins 1 & 2 closed |
|
BIOS type select EPROM |
JP2 |
Pins 2 & 3 closed | |
|
|
Power good signal detect from board |
JP5 |
Pins 1 & 2 closed |
|
Power good signal detect from power supply |
JP5 |
Pins 2 & 3 closed | |
|
|
ROM disk enabled |
JP6/pins 5 & 6 |
Open |
|
ROM disk disabled |
JP6/pins 5 & 6 |
Closed | |
|
|
CMOS memory normal operation |
JP11 |
Pins 1 & 2 closed |
|
CMOS memory clear |
JP11 |
Pins 2 & 3 closed | |
|
|
Primary serial port enabled |
JP13 |
Open |
|
Primary serial port disabled |
JP13 |
Closed | |
|
|
Secondary serial port enabled |
JP14 |
Open |
|
Secondary serial port disabled |
JP14 |
Closed | |
|
|
IDE interface enabled |
JP16 |
Open |
|
IDE interface disabled |
JP16 |
Closed | |
|
|
Floppy drive interface enabled |
JP17 |
Open |
|
Floppy drive interface disabled |
JP17 |
Closed | |
|
|
Watchdog timer enabled |
JP18 |
Closed |
|
Watchdog timer disabled |
JP18 |
Open | |
|
|
Factory configured - do not alter |
JP19 |
Unidentified |
|
|
Factory configured - do not alter |
JP20 |
Unidentified |
|
|
Factory configured - do not alter |
JP21 |
Unidentified |
|
|
Factory configured - do not alter |
JP22 |
Unidentified |
|
|
Watchdog timeout by NMI disabled |
JP23 |
Open |
|
Watchdog timeout by NMI enabled |
JP23 |
Closed | |
|
|
Factory configured - do not alter |
JP24 |
Closed |
|
Serial port 1 COM select COM1 |
JP26 |
Pins 1 & 2 closed | |
|
Serial port 1 COM select COM3 |
JP26 |
Pins 2 & 3 closed | |
|
Serial port 2 COM select COM2 |
JP27 |
Pins 1 & 2 closed | |
|
Serial port 2 COM select COM4 |
JP27 |
Pins 2 & 3 closed | |
|
SIMM CONFIGURATION | ||
|
Size |
Bank 0 |
Bank 1 |
|
512KB |
(2) 256K x 9 |
None |
|
1MB |
(2) 256K x 9 |
(2) 256K x 9 |
|
2MB |
(2) 1M x 9 |
None |
|
4MB |
(2) 1M x 9 |
(2) 1M x 9 |
|
8MB |
(2) 4M x 9 |
None |
|
16MB |
(2) 4M x 9 |
(2) 4M x 9 |
|
CPU SPEED SELECTION | ||||
|
Speed |
JP3 |
JP4 |
JP9 |
JP10 |
|
33MHz |
Closed |
Open |
2 & 3 |
2 & 3 |
|
40MHz |
Open |
Closed |
1 & 2 |
1 & 2 |
|
50iMHz |
Open |
Open |
1 & 2 |
2 & 3 |
|
Note: Pins designated should be in the closed position. | ||||
|
DMA CHANNEL SELECTION | ||
|
Channel |
JP25 |
JP30 |
|
1 |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
3 |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
PARALLEL PORT SELECTION | ||
|
Setting |
JP15 |
JP28 |
|
Disabled |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
SPP |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
|
EPP |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
|
ECP |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
SERIAL PORT 1 INTERRUPT SELECTION | |||
|
Setting |
JP29 |
JP31 |
JP32 |
|
IRQ10 |
Pins 4 & 7 closed |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
|
IRQ11 |
Pins 3 & 4 closed |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
|
IRQ12 |
Pins 4 & 5 closed |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
|
SERIAL PORT 2 INTERRUPT SELECTION | |||
|
Setting |
JP29 |
JP31 |
JP32 |
|
IRQ10 |
Pins 2 & 6 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
|
IRQ11 |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
|
IRQ12 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
|
FLASH DISK SELECTION | ||
|
Disk |
JP6/pins 1 & 2 |
JP6/pins 3 & 4 |
|
A |
Closed |
Closed |
|
B |
Open |
Closed |
|
C |
Closed |
Open |
|
D |
Open |
Open |
|
BIOS SELECTION | ||||
|
Type |
JP7/pins 1 & 2 |
JP7/pins 3 & 4 |
JP7/pins 5 & 6 | |
|
Flash |
Closed |
Closed |
Open | |
|
128KB |
Open |
Closed |
Open | |
|
256KB |
Closed |
Open |
Open | |
|
512KB |
Open |
Open |
Open | |
|
BASE ADDRESS SELECTION | ||||
|
Address |
JP8/pins 1 & 2 |
JP8/pins 3 & 4 |
JP8/pins 5 & 6 | |
|
CA00 |
Closed |
Closed |
Closed | |
|
CE00 |
Closed |
Closed |
Open | |
|
D000 |
Closed |
Open |
Closed | |
|
D400 |
Closed |
Open |
Open | |
|
D800 |
Open |
Closed |
Closed | |
|
DC00 |
Open |
Closed |
Open | |
|
E00O |
Open |
Open |
Open | |