IPTool.net.ua IPTools.net.ua

AP-5200SH

LANNER ELECTRONICS, INC.

AP-5200SH

Device Type

Mainboard

Processor

Pentium

Processor Speed

75/90/100/120/133/150/166/180/200MHz

Chip Set

SIS

Video Chip Set

Unidentified

Maximum Onboard Memory

64MB (EDO supported)

Maximum Video Memory

Unidentified

Cache

256/512KB

BIOS

Award

Dimensions

Unidentified

I/O Options

Floppy drive interface, green PC connector, IDE interface, parallel port, PS/2 mouse port, serial ports (2), VGA port, cache slot, IR connector

NPU Options

None

CONNECTIONS

Purpose

Location

Purpose

Location

Power LED & keylock

C1

PS/2 mouse port

CN4

IDE interface LED

C2

Serial port 1

CN5

Turbo LED

C3

IDE interface

CN6

Speaker

C4

Floppy drive interface

CN7

Green PC connector

C5

Parallel port

CN8

Reset switch

C6

Serial port 2

CN9

Auxiliary keyboard connector

CN1

IR connector

IR1

Power connector

CN2

Cache slot

SL1

VGA port

CN3

   

USER CONFIGURABLE SETTINGS

Function

Label

Position

Factory configured - do not alter

JP2

Closed

Factory configured - do not alter

JP3

Pins 1 & 2 closed

 

Power good signal detect from power supply

JP5

Pins 2 & 3 closed

 

Power good signal detect from board

JP5

Pins 1 & 2 closed

Factory configured - do not alter

JP8

Unidentified

Factory configured - do not alter

JP9

Unidentified

Factory configured - do not alter

JP10

Unidentified

SIMM CONFIGURATION

Size

Bank 0

8MB

(2) 1M x 36

16MB

(2) 2M x 36

32MB

(2) 4M x 36

64MB

(2) 8M x 36

Note: Board accepts EDO memory.

CACHE CONFIGURATION

Size

SL1

256KB

256KB module installed

512KB

512KB module installed

CACHE JUMPER CONFIGURATION

Type

JP6

JP7

Asynchronous

Pins 1 & 2 closed

Pins 1 & 3, 2 & 4 closed

Pipeline burst

Pins 2 & 3 closed

Pins 3 & 5, 4 & 6 closed

VIDEO MEMORY CONFIGURATION

Note: the size & location of the video memory is unidentified.

CPU SPEED SELECTION

CPU speed

Clock speed

Multiplier

JP1

JP4

75MHz

50MHz

1.5x

3 & 4

Open

90MHz

60MHz

1.5x

1 & 2

Open

100MHz

66MHz

1.5x

Open

Open

120MHz

60MHz

2x

1 & 2

3 & 4

133MHz

66MHz

2x

Open

3 & 4

150MHz

60MHz

2.5x

1 & 2

1 & 2, 3 & 4

166MHz

66MHz

2.5x

Open

1 & 2, 3 & 4

180MHz

60MHz

3x

1 & 2

1 & 2

200MHz

66MHz

3x

Open

1 & 2

Note: Pins designated should be in the closed position.

WATCHDOG TIMER ACTIVE SELECTION

Time out

J1

 

.5 sec

Pins 2 & 3 closed

 

1 sec

Pins 5 & 6 closed

 

2 sec

Pins 8 & 9 closed

4 sec

Pins 11 & 12 closed

 

8 sec

Pins 10 & 11 closed

 

16 sec

Pins 7 & 8 closed

 

32 sec

Pins 4 & 5 closed

 

64 sec

Pins 1 & 2 closed

WATCHDOG TIMER ACTIVE SELECTION

Setting

JP11

Reset system

Pins 1 & 2 closed

 

NMI system

Pins 2 & 3 closed

 

Disabled

Open