IPTool.net.ua IPTools.net.ua

GP-4032

BCM ADVANCED RESEARCH, INC.

GP-4032

Data bus:

32-bit, VL-bus

Size:

Three/quarter-length, full-height card

Hard drive supported:

Two IDE (AT) Interface drives

Floppy drives supported:

Two 360KB, 720KB, 1.2MB, 1.44MB, or 2.88MB drives

CONNECTIONS

Function

Location

40-pin IDE(AT) Interface connector

J1

10-pin serial port (COM1/2/3) - internal

J2

25-pin parallel port (LPT1/2) - external

J3

34-pin control cable connector - floppy drive

J4

10-pin serial port (COM2/3/4) - internal

J5

15-pin video feature connector - internal

J6

15-pin analog VGA port - external

J7

PORT CONFIGURATION SETTINGS

J4

J2

J5

J3

JP1

JP2

JP3

JP4

JP5

Enabled

COM1

COM2

LPT1

1 & 2

1 & 2

2 & 3

2 & 3

1 & 2

Enabled

COM1

COM2

LPT2

2 & 3

1 & 2

2 & 3

2 & 3

1 & 2

Enabled

COM3

COM4

LPT2

1 & 2

2 & 3

2 & 3

2 & 3

1 & 2

Enabled

COM2

COM3

LPT1

2 & 3

2 & 3

2 & 3

2 & 3

1 & 2

Disabled

COM1

COM2

LPT1

1 & 2

1 & 2

2 & 3

1 & 2

2 & 3

Disabled

COM1

COM2

LPT2

2 & 3

1 & 2

2 & 3

1 & 2

2 & 3

Disabled

COM3

COM4

LPT2

1 & 2

2 & 3

2 & 3

1 & 2

2 & 3

Disabled

COM2

COM3

LPT1

2 & 3

2 & 3

2 & 3

1 & 2

2 & 3

Enabled

Disabled

Disabled

Disabled

1 & 2

2 & 3

2 & 3

2 & 3

2 & 3

Disabled

Disabled

Disabled

Disabled

2 & 3

2 & 3

2 & 3

2 & 3

2 & 3

Note:Pins designated should be in the closed position.

USER CONFIGURABLE SETTINGS

Function

Location

Setting

Parallel port is uni-directional (printer)

JP6

pins 1 & 2 closed

 

Parallel port is bi-directional (scanner)

JP6

pins 2 & 3 closed

Hard drive enabled

S1

pins 1 & 2 closed

 

Hard drive disabled

S1

pins 2 & 3 closed

VGA WAIT STATE SELECTION

Wait state

JP8

JP9

 

1

pins 2 & 3 closed

pins 2 & 3 closed

2

pins 2 & 3 closed

pins 1 & 2 closed

 

3

pins 1 & 2 closed

pins 2 & 3 closed

 

4

pins 1 & 2 closed

pins 1 & 2 closed

MISCELLANEOUS TECHNICAL NOTES

The location of jumpers JP7, JP10, JP11, S2, S3, and S4 was not presented by the manufacturer.

These jumpers are factory configured to: JP7 - closed, JP10 - pins 1 & 2 closed, JP11 - pins 1 & 2 closed, S2 - pins 2 & 3 closed, S3 - pins 1 & 2 closed, S4 - pins 1 & 2 closed; do not alter.