ACCULOGIC, INC.
SIDE-4
|
| |
|
Data bus: |
16-bit, ISA |
|
Size: |
Half-length, full-height card |
|
Hard drives supported: |
Two IDE(AT) drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
34-pin control cable connector-floppy drive |
J1 |
|
4-pin connector-Drive Active LED |
J2 |
|
9-pin serial port 1-external |
J3 |
|
25-pin parallel port-external |
J4 |
|
40-pin AT Interface (IDE) connector |
J5 |
|
9-pin serial port 2-internal |
J8 |
|
IRQ14 STATUS | |||
|
Function |
W3/Pins 1 & 2 |
W3/Pins 3 & 4 | |
|
IRQ14 normal |
open |
closed | |
|
IRQ14 delayed until ACTIVE- signal is removed |
closed |
open | |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
Floppy drive enabled |
W4A |
closed | |
|
Floppy drive disabled |
W4A |
open | |
|
Floppy drive port address is 3F0-3F7h |
W4B |
open | |
|
Floppy drive port address is 370-377h |
W4B |
closed | |
|
Single speed floppy drives supported |
W5 |
open | |
|
Dual speed floppy drives supported |
W5 |
closed | |
|
Hard drive enabled |
W9 |
closed | |
|
Hard drive disabled |
W9 |
open | |
|
PARALLEL PORT (CN4) CONFIGURATION | ||
|
CN4 |
W8/jumper 1 |
W8/jumper 2 |
|
LPT1 enabled |
closed |
open |
|
LPT2 enabled |
closed |
closed |
|
Disabled |
open |
open |
|
SERIAL PORT 1 (CN3) CONFIGURATION | |||
|
Function |
W8/Jumper 3 |
W8/Jumper 4 | |
|
Serial port 1 set to COM1 (3F8h) |
closed |
open | |
|
Serial port 1 set to COM3 (3E8h) |
open |
closed | |
|
SERIAL PORT 2 (CN8) CONFIGURATION | |||
|
Function |
W8/Jumper 5 |
W8/Jumper 6 | |
|
Serial port 2 set to COM2 (2F8h) |
closed |
open | |
|
Serial port 2 set to COM4 (2E8h) |
open |
closed | |
|
I/O PORT INTERRUPT REQUEST | |||
|
Function |
Location |
Setting | |
|
Parallel port (CN4) uses IRQ7 |
W7 |
pins 3 & 4 closed | |
|
Parallel port (CN4) uses IRQ5 |
W7 |
pins 1 & 2 closed | |
|
Serial port 2 (CN8) uses IRQ3 |
W7 |
pins 5 & 6 closed | |
|
Serial port 2 (CN8) uses IRQ4 |
W7 |
pins 5 & 7 closed | |
|
Serial port 1 (CN3) uses IRQ4 |
W7 |
pins 7 & 8 closed | |
|
Serial port 1 (CN3) uses IRQ3 |
W7 |
pins 6 & 8 closed | |
|
MISCELLANEOUS TECHNICAL NOTES |
|
This controller has no on-board software. |